出租挖掘机也要结合机械的实际进行

日期:2018-05-18   来源:http://www.yueqi0448.cn/
  在现有挖机的基础上改装蒸发器(空调不变)、水箱散热器及液压散热器,并在水箱散热器和液压散热器之间留出五公分的空间,装上蒸发器,然后再把它们的两边封好,使外界空气不能进入。

  On the basis of the existing excavators, the evaporator (air conditioner), radiator and hydraulic radiator are reformed, and five centimeters of space is left between the radiator and the hydraulic radiator, and the evaporator is installed, and then both sides are sealed so that the outside air can not be entered。

  使用这种方式(热力膨胀阀)可制冷至零下5~10度。发动机的风扇把冷空气吸入,液压散热器和水箱散热器进行热交换后降温,后吹向发动机及大泵上冷却。

  In this way, the thermal expansion valve can be refrigerated to zero 5~10 degrees. The fans of the engine suck the cold air, heat the hydraulic radiator and radiator, then cool down, and finally blow to the engine and the big pump to cool down.

  如果发动机及液压的温度低于50摄氏度,那么压缩机就会停机;高于75摄氏度,那么制冷压缩机便会自动工作。这时只有确保发动机及液压系统的温度在50~60摄氏度以内,挖机才能正常运行,并达到佳运行效果。
长臂挖掘机出租

  If the engine and hydraulic temperature is below 50 degrees Celsius, the compressor will stop; if the temperature is above 75 degrees Celsius, then the refrigeration compressor will work automatically。 At this time, only to ensure that the engine and hydraulic system temperature within 50~60 degrees Celsius, the excavator can run normally, and achieve the best operation results。

  桩体挠曲矫正。腹向弯曲矫正是将拉森钢板桩变曲段的两端固定的支承点上,用设置在龙门式顶梁架上的千斤顶顶在钢板桩凹凸处进行冷弯矫正

幸运飞艇套利方法  The deflection correction of the pile body. The abdominal bending correction is the support point fixed on the two ends of the Larsen steel sheet pile, and the jack top on the Longmen type top beam is corrected by cold bending at the concave and convex section of the steel sheet pile.

  侧向弯曲矫正通常在专门的矫正平台上进行,将拉森钢板桩弯曲段的两端固定在矫正平台的支座上,用设置在拉森钢板桩的弯曲段侧面矫正平台上的千斤顶顶压拉森钢板桩弯凸处,进行冷弯矫正。

  The lateral bending correction is usually carried out on the special correction platform. The ends of the bending section of the Larsen steel sheet pile are fixed on the support of the correction platform. The bending section of the jack top pressure Larsen steel sheet pile on the platform is corrected with the side of the bending section of the Larsen steel sheet pile to be corrected by cold bending.

  表面缺陷矫正。先清洗缺陷附近表面的锈蚀和油污,然后用焊接修补的方法补平,再用砂轮磨平。

  Correction of surface defects。 First, clean the rust and oil stains near the surface of the defects, then repair them by welding and then grind them。

  本文的精彩内容来自加长臂挖掘机出租详细内容请点击我们的官方网站:http://www.yueqi0448.cn/谢谢您的到来!

  The highlights of this article are from the detailed description of the long arm excavator rental. Please click on our official website: http://www.yueqi0448.cn/, thank you for coming.

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】

幸运飞艇有什么技巧 幸运飞艇稳杀2码 幸运飞艇号码规律 幸运飞艇是不是坑人的 幸运飞艇有什么技巧 幸运飞艇冠军五码公式 全天幸运飞艇最精准计划群 幸运飞艇登陆 幸运飞艇骗局真相 幸运飞艇套利方法